![]() v1.18.4 available on amd64, arm64 & armhf.v1.18.5 available on amd64, arm64 & armhf.v1.18.6 available on amd64, arm64 & armhf.v1.19.0 available on amd64, arm64 & armhf.v1.19.1 available on amd64, arm64 & armhf. ![]() v1.19.2 available on amd64, arm64 & armhf.v1.20.0 available on amd64, arm64 & armhf.v1.20.1 available on amd64, arm64 & armhf.v1.20.2 available on amd64, arm64 & armhf.v1.20.3 available on amd64, arm64 & armhf.v1.20.4 available on amd64, arm64 & armhf.v1.21.0 available on amd64, arm64 & armhf.v1.22.0 available on amd64, arm64 & armhf.v1.22.1 available on amd64, arm64 & armhf.v1.22.2 available on amd64, arm64 & armhf.syncthing-gael will now use core22 as most of the users are on Ubuntu 22.04.v1.23.0 available on amd64, arm64 & armhf.v1.23.1 available on amd64, arm64 & armhf.v1.23.2 available on amd64, arm64 & armhf.v1.23.3 available on amd64, arm64 & armhf.The v1.18.4 is backward compatible with the old versions and will use old config paths when appropriate. Starting with v1.18.4 config is now stored by default in $SNAP_DATA and shared folders in $SNAP_COMMON. In v1.18.3 config was still in $SNAP_USER_COMMON but newly configured shared folders were in $SNAP_COMMON by default (as it always should have been). This version will first be available on the edge channel.įrom v1.14.0 to v1.18.2 this snap used $SNAP_USER_COMMON as the home for config and shared folders. To configure your new node visit Read the doc at on how to get started.Īs of v1.22.3-rc.2 syncthing-gael will use core22 as most of the users are on Ubuntu 22.04. Your data is your data alone and you deserve to choose where it is stored, whether it is shared with some third party, and how it's transmitted over the internet. It synchronizes files between two or more computers in real time, safely protected from prying eyes. Syncthing is a continuous file synchronization program. Please see proxying.This is NOT an original piece of work, just a snap of syncthing Syncthing can use a SOCKS5 proxy for outbound connections. This still works even if Syncthing is bound to listen on localhost This will bind to your local port 9999 and forward all connections from there to port 8384 Start a tunnel with a command like the following: GUI port to the outside world, you can access it through a SSH tunnel instead. If you have SSH access to the machine running Syncthing but would rather not open the web Port in your local firewall if you have one. To be able to access the web GUI from other computers, you need to change the GUI Listen Address setting from the default 127.0.0.1:8384 to 0.0.0.0:8384. In case you installed Syncthing manually you can follow the instructions to manually add the syncthing preset You can then verify that the ports mentioned above are allowed: If you also want to allow external access to the Syncthing web GUI, run:Īllowing external access is not necessary for a typical installation. , you can allow the necessary ports by running: If you’re using ufw on Linux and have installed the Syncthing package Port 21027/UDP (for discovery broadcasts on IPv4 and multicasts on IPv6).Port 22000/TCP (or the actual listening port if you have changed the Sync Protocol Listen Address setting.).If your PC has a local firewall, you will need to open the following ports for incoming In the absence of port forwarding, relaying may work well enough to get devices connectedĪnd synced, but will perform poorly in comparison to a direct connection. Therefore if you set up port forwards for oneĭevice, other devices will be able to connect to it even when they are behind a NAT 22000/TCP).Ĭommunication in Syncthing works both ways. The external forwarded portĪnd the internal destination port has to be the same (i.e. Or the port set in the Sync Protocol Listen Address setting. If this is not possible or desirable you should set up a port forward for port 22000/TCP, If it succeeds you will see a message in theĬreated UPnP port mapping for external port XXXXX on UPnP device YYYYY. If you have a NAT router which supports UPnP, the easiest way to get a working portįorward is to make sure UPnP setting is enabled on both Syncthing and the router –
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |